Case Study : Dell Laptop
Part No : QAL80 LA-7781P
Problem : No Display
Solution : Found that only stuck in 0.150 amp on PSU. Step down Ic (3.3 v /5 v ) heating.
Checked For short Circuit Not Found. Then checked the RTC 3.3 v it was 0 volt Replaced RTC Cell Then Also no voltage RTC. At Last Found Pf Leaky
Laptop Working Fine
Electronicz Repair Guide
Repair Guide for those who want to learn to repair there own gadgets
Wednesday, January 3, 2018
Tuesday, January 2, 2018
Acer Aspire E5-573 No Power On and Not Charging
Model:Acer Aspire E5-573
MB ID:ZRT
Case Study Problem : plugged in adaptor no power on and not charging
Solution : First I check VIN present, no auxuliary voltages at battery connectors.
I check with PSU 19V, it takes 0.28amp then decrease voltage from 19v to 17v.
now the laptop power on and working fine. So the problem is located at the power IC pin(6) 2.59v (acdet).
I check voltage divider working ok as in schematic
Now I replace 8k resistance in place of 10k now am getting voltage is 2.13v (63.4k-10k actual)
ok i give 19v from PSU ...LAPTOP is working fine.
MB ID:ZRT
Case Study Problem : plugged in adaptor no power on and not charging
Solution : First I check VIN present, no auxuliary voltages at battery connectors.
I check with PSU 19V, it takes 0.28amp then decrease voltage from 19v to 17v.
now the laptop power on and working fine. So the problem is located at the power IC pin(6) 2.59v (acdet).
I check voltage divider working ok as in schematic
Now I replace 8k resistance in place of 10k now am getting voltage is 2.13v (63.4k-10k actual)
ok i give 19v from PSU ...LAPTOP is working fine.
Labels:
Acer Laptop,
Board Repair,
Boardlevel,
Laptop Repair,
No Power On,
Not Charging
Friday, December 29, 2017
Old Motherboard Auto On and Can't Save Time
Old Motherboard Auto On and Can't Save Time
Problem: Auto on and can't saved time even though it was replaced with a new CMOS battery.
Action taken: Check crystal oscillator no luck, resolder frequency generator no luck, check two 22pf 1 is shorted so have to replace.
Problem: Auto on and can't saved time even though it was replaced with a new CMOS battery.
Action taken: Check crystal oscillator no luck, resolder frequency generator no luck, check two 22pf 1 is shorted so have to replace.
Friday, July 15, 2011
Resetting Ink Level on Canon Printer MX300
Each print a document or image, then the level of ink in the cartridge will be reduced and a time will run out. Maybe you can refill the printer cartridges, but your computer will continue to detect that the cartridge is empty, and your printer will not print any documents.
Thursday, July 14, 2011
Error E27 on Canon MP198/MP258 “Ink Absorber is Full”,
Not just counting how many times the printer is done printing, the printer also calculate how many times do the head cartridge cleaning, and ink absorber on the printer you will be considered full at a later time. Error code at the beginning was the E8 and then will turn into E27.
The following is the step by step how to reset error “Ink Absorber is Full” with error code E8 of E27 on Canon printer model MP198 and MP258 (or may be also work on MP270):
The following is the step by step how to reset error “Ink Absorber is Full” with error code E8 of E27 on Canon printer model MP198 and MP258 (or may be also work on MP270):
Wednesday, July 13, 2011
Resetting Epson C45
The Epson C45 printer ink cartridges could be refilled manually. Unfortunelly, although the ink tank already refilled but the run out/empty ink message will still appear and printer stop to run. Reset can be done if the premises software does not work sometimes have to use the resetter. The following tutorial will explain how to reset ink level of Epson C45 by using application program SSC Service Utility.
Tuesday, July 12, 2011
Resetting Canon IP 1600 ink counter
Error code blink green 4 times and orange 1 time that means the ink runs out. you can reset it manually or using resetter program. In this tutorial using a method resetter IPTool:
Subscribe to:
Posts (Atom)